Apple official website recommended.
PRODUCT DETAILS
- Meross HomeKit Hub is needed for installation.
-
Works with Apple HomeKit and is compatible with SmartThings.
- Voice Access: Know the status of the device via HomePod / Siri.
- Alert: Your Meross app or Apple Home app will receive an alert instantly when leakage is detected.
- Sound Alarm: Up to about 60dB when alarming.
- Low Power Consumption: Up to 18 months lifespan with the built-in battery.
- Automation: Set triggers to control other Meross devices in the Meross app.
- IP67 Waterproof.
- Control Up to 16 Devices: One hub is able to control 16 Meross devices (sensors, detectors, thermostat valves) at the same time.
Smart Wi-Fi Hub
MSH300HK
- Compact housing, size 5.8 x 4.1 x 2.1 cm.
- Support both 802.11n Wi-Fi.
- Bridge your Meross low-power-consumption smart devices, such as smart sensors and smart thermostat valves, to the Internet.
- Works with the Wi-Fi you already have.
WORKS WITH
PRODUCT SPECIFICATION
Battery: |
CR123A Battery, replaceable |
Alarm Volume: |
About 60 dB (A) at 1m (3ft). |
Sensor Dimensions (Dia × H): |
φ71.5 × 41.5 mm (φ2.81 × 1.63 in.) |
Hub Dimensions (W × D × H): |
59 × 41 × 21 mm (2.3 × 1.6 × 0.8 in. |
Wireless Standard: | Smart Hub: 802.11 b/g/n 2.4GHz Wi-Fi 433MHz Smart Water Leak Sensor: 433MHz |
Certifications: |
FCC |
Package Contents: | 1 × Smart Sensor 1 × User Manual 1 × Conductor 1 × Power Adapter (Kit Version) 1 × USB Cable (Kit Version) 1 × Smart Hub (Kit Version) |
System Requirements: |
Smartphone running iOS 10 * or later,
Android 6.0 or later
Existing Wi-Fi network
*HomeKit version requires iOS 13.0 or later
|
Environment: | Operating Temperature: 0°C~40°C (32°F~104°F) Storage Temperature: -40°C~70°C (-40°F~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing |
FAQS
Double click on the Hub and see the green LED flashing which indicates that the Hub is in pairing mode.
Use the conductor for quick connection of contacts "1 & 2" or contacts "1 & 3" and repeat 3 times in 2 seconds to start pairing with the Hub (within 2 minutes). The snesor LED will flash quickly when pairing.
Improper contact between the probe of the wire and the sensor short contact time will lead to the failure and the LED will not blink. In this case, you can wet your fingers and touch the contact point "1 & 2" or "1 & 3" 3 times (within 2 seconds) with your fingers instead of the wire to make the sensor into pairing moede and the LED will blink.
If you have been using it for a long time, the battery might be dead. Please replace the battery and follow the instructions above.
When there is water flowing through the sensor (on contact 1&2 or 1&3) for more than 3 seconds, the sensor will determine the leakage.
Under normal circumstances, sensor will be in low power mode and the battery can last for 18 months. If the power is depleted, you can replace it with a CR123A battery.
Yes, you can. Specifically, the following.
If you are using the HomeKit version of the Hub (the Hub has a Setup Code with an 8 as a number), this Hub supports all sub-devices in the Meross app (which needs to be updated to the latest firmware). All sub-devices except MTS100 and MS100 can be used with this Hub for HomeKit functionality.
If you are using the Non-HomeKit version of the Hub (no Setup Code on the Hub), this Hub only supports MTS100, MS100 2 products in the Meross app and does not support HomeKit functionality.
A Meross Smart Hub can support up to 16 devices.
RESOURCES
Download the Manual for Smart Water Leak Sensor Kit, MS400HHK (PDF) here.